Best configuration SVP for my system (Page 2 of 5)

Michael
What monitor resolution do you have?

Michael
I did not know what you are so hard man.

I checked GPU load when play video with SVP at my TV via HDMI with mode 1920x1080 @ 60 Hz.
My GTX 660 Ti with madVR on default setting FullHD shows GPU load at 20%. And 24% with sharpen complex 2 shader enabled.
720p shows 16% / 17% (without/with sharen complex 2).
GTX 660 Ti has 1344 SPs, GT 640 has 384 SPs. So GT 640 is slower in 1344/384 = 3.5 times. It must be enough for madVR at default settings.

Default settings you can get by launching madVR\restore default settings.bat from SVP folder.

I checked GPU load at your's maniacal madVR settings (Jinc 4 taps / spline 4 taps / spline 4 taps).
FullHD shows 43% / 49 % (without/with sharen complex 2).
720p shows 27% / 30 % (without/with sharen complex 2).

GTX 650 Ti (768 SPs) is minimum for such settings. If you don't want more complicated GPU processing

Michael
Yes

overclocked ati 7850 is enough (very cheap)

Michael
What video card I can buy
MAG79
GTX 650 Ti (768 SPs) is minimum for such settings

Michael
madVR in maximum mode
Tell what you mean when say "maximum mode" and I will can to measure GPU load at my system at these settings.

Michael
Jinc / Jinc / Jinc
You are seriously? You want just heavy settings. But heavy settings is not equal to better settings
Better setting are settings by default

The taps are what?
It is parameter that controls count of input samples. You may google it.

Thanks for the info;)

Unfortunately I still can not giardare a movie in Full HD (1080p) with MadVR. If I use it, the audio and video out of sync and goes a bit in slow motion.

To see the video, I put the default renderer mpchc (system default).

I also noticed that watching a video SD cartoon, any settings you put with MadVR, there is loss of frame (dropped frames).

Grazie per le informazioni

Purtroppo non riesco ancora a giardare un filmato in full hd (1080p) con MadVR.  Se lo uso, l'audio e fuori sincro e il video va un poco al rallentatore.

Per vedere il video, devo mettere il renderer predefinito di mpchc (predefinito del sistema).

Ho anche notato che guardando un video SD cartone animato, qualsiasi impostazione metto con MadVR, si verifica la perdita di frame (dropped frame).

I've been reading this forum from time to time to get my SVP configured properly and after reading this, I simply HAD to register.

The benchmarks you posted are for 3D rendered video games, which is not an accurate or honest way to compare AMD's APU's with Intel's HD 4000. Why? We're discussing an APU's ability to render/decode/transcode by using it's integrated GPU for the mathematical calculations, typically referred to as Quicksync or a form of iGPU acceleration.

If the video format is the supported H.264, MPEG2, or VC-1... a QuickSync enabled Intel processor will absolutely DESTROY even the fastest AMD graphics card or CPU while Decoding/Transcoding/Encoding. It even beats the heck out of my GTX680!!

And QuickSync hardware decoding is included in the latest FFdshow

here:

Or more here: http://www.anandtech.com/show/5771/the- … -review/21

MAG79
True, but I have the best of both worlds. VirtuMVP software lets me use both the HD4000 QuickSync (for LAV and ffdshow) and my GTX 660 for SVP at the same time. Works great.

Hello, I am new here
I have a problem again. Suddenly two days ago, without my having changed the settings that I have written in previous messages, movies FHD (1080) are all slowed down. The sound feels good, but the video is jerky and slow motion. What can it be?

==============================================================

ORIGINAL MESSAGE

Ciao, sono di nuovo qui
ho di nuovo un problema. All'improvviso due giorni fa, senza che io abbia modificato le impostazioni che ho scritto nei messaggi precedenti, i filmati FHD (1080) sono tutti rallentati. L'audio si sente bene, ma il video va a scatti e al rallentatore. Cosa può essere?