Topic: AMD Phenom II X4 940 Black Edition and Evga GTX 260 216 Core GPU

Hello,

I would like to say thank you for this sweet software. The quality of smooth video rendering with 60fps is awesome.

However, I am experiencing some motion jitters during fast motion sequences. I have been going through a lot of settings and configurations throughout this forum and a lot of trial and errors with this software setup to get the optimize settings for my hardware without receiving any banding or halo rings as well as motion jitter during fast action sequences but I keep hitting a dead-end.

Those are the only problem I am having among every one else and I know it all depends on the hardware specifications.

Here are my specs:

Computer: Computer:      GIGABYTE GA-MA790X-UD4P
CPU:           AMD Phenom II X4 940 Black Edition (Deneb, RB-C2 (Ridgeback))
               3000 MHz (15.00x200.0) @ 3000 MHz (15.00x200.0)
Motherboard:   GIGABYTE GA-MA790X-UD4P
Chipset:       AMD 790X (RD780) + SB750/SB710

Graphics:      EVGA e-GeForce GTX 260
               nVIDIA GeForce GTX 260, 896 MB GDDR3 SDRAM

Monitor Info: LG W2361
Supported Video Modes:

  • 1680 x 1050 @ 60 Hz
           1280 x 1024 @ 75 Hz
           1280 x 1024 @ 60 Hz
           1152 x 864 @ 75 Hz
           1920 x 1080 @ 510 x 290 mm, Pixel Clock 138.50 MHz
           1920 x 1080 @ 520 x 290 mm, Pixel Clock 148.50 MHz

Max. Vertical Size: 29 cm
Max. Horizontal Size: 51 cm
Horizontal Freq: 30 -83 KHz
Vertical Freq: 56 - 61 Hz
Maximum Pixel Clock: 150 MHz

I hope that I was clear in what I was asking for. Thanks.

http://img.overpic.net/thumbs/x/3/3/xx33gmza8wc5kdpr8hq4t_s.png

  • Rimsky
  • Installer Master
  • Offline

Re: AMD Phenom II X4 940 Black Edition and Evga GTX 260 216 Core GPU

cyntek
did you try Reclock?

Re: AMD Phenom II X4 940 Black Edition and Evga GTX 260 216 Core GPU

http://www.svp-team.com/forum/viewtopic … 114#p35114

  • MAG79
  • SVP developer
  • Offline

Re: AMD Phenom II X4 940 Black Edition and Evga GTX 260 216 Core GPU

cyntek
Does tearing test line moves flawlessly without jitter and stops?
SVP tray menu - Tearing test

5 Reply by cyntek (edited by cyntek 06-10-2013 04:58:39)

Re: AMD Phenom II X4 940 Black Edition and Evga GTX 260 216 Core GPU

Rimsky
Yes.

MAG79
Tearing test lines moves flawlessly without jitter. However, in fullscreen mode it slightly skips /or jitters.

I changed a few settings in FFDshow and disabled all codecs and enabled only Raw video. So I believe that fixed my jitter troubles.

Now, I seem to be dropping frames and it seems to be rising pretty slowly compared to the drawn frames which is much higher compared to dropped frames so all in all I'm pretty much satisfied.

And I have changed from using LAV Video Decoder from within MPC-HC 1.7.0.7858. Since LAV Video Decoder was dropping frames like crazy, I decided to go with EVR C/P.


http://oi39.tinypic.com/1fwe2u.jpg